Frequently Ask Question

Yes. XPEL film can be applied over a vinyl wrap or graphics. However, if there are any hard edges that film must cross (as in the case of stripes), it could result in some air being trapped along that edge.

Yes, XPEL can be installed on your cars headlamps and fog lamps

We recommend using the XPEL Rinse Free Car Wash, combined with the XPEL Detail Spray and Ceramic Boost for increased cleanliness and slickness

Yes. Though you can install the film over any quality of touch-up, the best possible appearance will be obtained if the touched up area has been color-sanded smooth and buffed after the application of the paint.

Yes. XPEL ULTIMATE PLUS can be applied to any smooth surface, though care should be taken around any electronics and/or switches so that installation fluids aren’t allowed to get into sensitive areas.

Yes, most factory paint is fully cured before the car ever leaves the assembly line.

XPEL Film Cleaner is generally designed to remove dirt, grime and oils from paint protection film that lead to yellowing over time. To remove stains from other substances such as insects, bird droppings or other compounds, use acetone or lacquer thinner with a soft microfiber cloth.

While the edge of the film can be seen from certain angles, people generally do not notice it unless they are looking for it. However, if the car is dirty and dust and dirt can collect along the edge of the film, it will be more noticeable. Once the car is cleaned, it will be once again difficult to detect unless looking for it.

The self-healing clear coat of our ULTIMATE PLUS and STEALTH films is designed to repair itself from swirl marks and light scratches from car washes, etc. If a piece of debris has penetrated all the way through the clear coat on the film, it will not self-heal. The only way to fix this would be to have the piece of film replaced.

The XPEL ULTIMATE PLUS Film Series warranty is transferable to another owner with proof of purchase.

No, the film once applied and removed cannot be reused.

Any of our paint protection films can be installed on aluminum or brushed metal, though they may change the appearance to some degree depending on the film you choose. We recommend having your installer apply a small swatch of the film to the surface in question to determine the appearance prior to full installation.

We recommend using our XPEL Flawless Finish Paint Protection Film Sealant. This product has been specially formulated for use with polyurethane paint protection films to provide the maximum protection and gloss, while containing no ingredients that would cause discoloration over time. We also recommend XPEL Detail Spray and/or Ceramic Boost for added slickness and ease of cleaning.

Waxes, sealants and protectants are typically designed to reduce the surface energy of the paint, making them easier to clean etc. A reduction in surface energy will reduce the film’s ability to adhere to the paint and could cause long term adhesion issues. Because of this, we generally recommend removing these types of products before installation. If these types of coatings are to be used, we recommend applying them AFTER installation of our paint protection film.

Yes, Coatings can be applied to the films. Adding a coating does not stop the film from self-healing. Coatings can add a protective layer over the film, which depending on the coating can provide different properties (Please contact your installer or coating company for more information). That additional coating layer, depending on the coating applied, may or may not self-heal. Once the coating wears down and deteriorates, the self-healing qualities of XPEL ULTIMATE PLUS and STEALTH will remain. We recommend XPEL FUSION PLUS Ceramic Coating. Our ceramic was specifically formulated for your vehicles paint and XPEL Paint protection film.

We would not recommend this, as it may result in poor adhesion to the painted surfaces. Professional removal of the ceramic coating is recommended. You may install XPEL FUSION PLUS on top of your XPEL Paint Protection Film. Check with your local installer for more details.

Yes, assuming you and the installer are both comfortable with the risk, there is nothing about the film that would prevent this from being done. We also have designs for most body panels on nearly every vehicle, which would allow installation without dismantling the vehicle.

Yes, you can install a vinyl on top of the film. We recommend waiting 48 hours after installation before doing so. You may also remove the stripe without damaging the film, if removed properly.

This is a very common occurrence with Paint Protection Film of all brands. It has to do with the difference in refractive index between the layer of film and the paint on the car. It is most noticeable on compound-curved surfaces because the film must be stretched over these areas to allow it to be installed without wrinkles. When the film is stretched, it becomes slightly thinner in those areas which causes the phenomenon seen through polarized glasses.

It can also occur on flat surfaces when the installer needs to use a drying solution (as opposed to a slip solution) such as alcohol and water to get the needed bond to the paint. This is due to the difference in viscosity of the fluids and their effect on the adhesive’s properties.

Polarized glasses have this effect on several different multi-layer surfaces (not just paint protection film) made of glass or plastic.