Film Care | Aftercare Assistance
ULTIMATE FUSION™ Paint Protection Film
ULTIMATE PLUS ™ Paint Protection Film
STEALTH ™ Paint Protection Film
PRIME ™ Automotive Window Film Care
Removing Paint Protection Film
ULTIMATE FUSION™ Paint Protection Film
To Keep Your Film Looking Great, Follow A Few Simple Guidelines:
- Wait 48 hours after installation to wash your car.
- Remove insect or other stains as soon as possible with XPEL Film Cleaner.
- Stubborn stains can be removed with 99% isopropyl alcohol. Take care to keep these chemicals off the vehicle’s paint.
- Seal with XPEL Ceramic Boost at least once every 6 months to preserve high gloss.
- Light scratches in the film will self-heal in 20-30 minutes at room temperature. In colder conditions, or to accelerate the process, pour warm water (120°F) over the affected area.
- Avoid using a pressure washer or high-pressure water source near the edges of the film, it can cause the film to lift and/or become damaged.
- Detailing Clay can be used to remove contaminants that are on the film.
ULTIMATE PLUS ™ Paint Protection Film
To Keep Your Film Looking Great, Follow A Few Simple Guidelines:
- Wait 48 hours after installation to wash your car.
- Remove insect or other stains as soon as possible with XPEL Film Cleaner.
- Stubborn stains can be removed with 99% isopropyl alcohol. Take care to keep these chemicals off the vehicle’s paint.
- Seal with XPEL Ceramic Boost at least once every 6 months to preserve high gloss.
- Light scratches in the film will self-heal in 20-30 minutes at room temperature. In colder conditions, or to accelerate the process, pour warm water (120°F) over the affected area.
- Avoid using a pressure washer or high-pressure water source near the edges of the film, it can cause the film to lift and/or become damaged.
- Detailing Clay can be used to remove contaminants that are on the film.
STEALTH ™ Paint Protection Film
To Keep Your Film Looking Great, Follow A Few Simple Guidelines:
- Wait 48 hours after installation to wash your car.
- Remove insect or other stains as soon as possible with XPEL Film Cleaner.
- Stubborn stains can be removed with 99% isopropyl alcohol or lacquer thinner. Take care to keep these chemicals off the vehicle’s paint.
- Seal with XPEL Ceramic Boost at least once every 6 months to preserve and maintain satin finish.
- Light scratches in the film will self-heal in 20-30 minutes at room temperature. In colder conditions, or to accelerate the process, pour warm water (120°F) over the affected area.
- Avoid using a pressure washer or high-pressure water source near the edges of the film, it can cause the film to lift and/or become damaged.
PRIME ™ Automotive Window Film Care
XPEL PRIME Automotive Window Films Were Designed To Keep Their Flawless Appearance And Clarity For Many Years. Follow These Tips To Properly Care For Your Windows And Keep Them Looking Their Best:
- Keep in mind that your window tint may have a hazy appearance or moisture bubbles for up to ten days after installation. These conditions will disappear once the moisture used to apply your tint dries up completely.
- Wait approximately 1-5 days after installation before rolling down or cleaning your windows based on the climate in which it was installed.
- Use a microfiber towel slightly dampened with water to clean your windows. If necessary, mild, non-ammonia glass cleaners may also be used.
- Avoid the use of abrasive materials such as scouring pads, to clean your tinted windows.
Removing Paint Protection Film
Professional Removal Of The Film Is Recommended. However, When Professional Removal Is Not Possible, The Film May Be Removed As Follows:
- Removal of paint protection film should be done with a steamer. It will keep the film pliable and wet so that it can be “stretched” off the vehicle.
- Peel one corner of the film up with your fingernail.
- Pull the film towards you at a shallow angle less than 45 degrees (see figure 8a). This angle is important to ensure sure that the adhesive comes off with the film rather than staying on the paint. The film should “stretch” off the car.
- If any adhesive is left on the car, use a general adhesive remover to help loosen it.
FUSION PLUS ™ Ceramic Coatings
Aftercare
Cleaning
Drying
Detailing
Spot Removal Of Surface Contamination
Vehicle Inspection Schedule
Aftercare
Using XPEL aftercare products when detailing your various surfaces will significantly extend the life of FUSION PLUS. Our products have been designed to complement our coatings and will help keep your surface looking newer, longer.
Cleaning
- For exterior cleaning, we recommend using XPEL Rinse Free Car Wash on a weekly basis, to avoid excessive contamination buildup. Avoid washing in direct sunlight to minimize streaking and water spotting.
- Wash from the roof downwards, leaving the dirtiest sections last, avoiding possible cross-contamination. You can follow up with XPEL Detail Spray and XPEL Ceramic Boost for added gloss.
- For interior cleaning, we recommend using XPEL Interior Cleaner (as needed) on your leather, plastics, and non-fabric surfaces. For fabric areas, we recommend vacuuming and using a clean, dry microfiber. We recommend testing in an inconspicuous area before applying XPEL Interior Cleaner – please read directions before applying.
Drying
- Always dry the exterior surfaces completely using a clean, soft, lint free microfiber towel or air blower. Never allow water to evaporate on its own. Tap water can contain minerals which leave deposits on your coating, creating unwanted water spots.
- For best results use XPEL Microfiber Towels, which have been designed to absorb water. Always avoid aggressive wiping.
Detailing
- For exterior surfaces, follow washing and drying steps above. Follow up with XPEL Detail Spray for any left- over fingerprints or smudges on your paint protection film or surface. You can apply the XPEL Ceramic Boost (as needed) for added shine and slickness.
- Avoid applying XPEL Detail Spray or XPEL Ceramic Boost in direct sunlight, to minimize streaking and water spotting.
Spot Removal Of Surface Contamination
- Never use aggressive products to polish the coating or to removing surface contamination.
- Visit your authorized XPEL FUSION PLUS installer for any questions you have on your coated surfaces.
Vehicle Inspection Schedule
To uphold the FUSION PLUS warranty, you must visit your FUSION PLUS certified installer (who applied your original coating), annually, during the duration of warranty. If you have had a change of address, please email warranty@xpel.com with any questions.